2.1 Object - This method of test covers the procedure for determining aggregate crushing value of coarse aggregate. NOTE 1 -The ‘aggregate crushing value’ gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggre

Get Price

The standard aggregate crushing test is made on aggregates passing IS 12.5 mm and retains on 10 mm. Place the sample in oven for a period of 4 hrs to make it

Get Price

Name of the experiment: Aggregate Crushing value test. Objective: 1. Determine the aggregate crushing value of coarse aggregate. 2. Assess suitability of coarse aggregates for use in different types of road. Theory: The “aggregate crushing value” give a relative measure of the resistance of an aggregate to crushing under gradually applied

Get Price

Abrasion Test is the measure of aggregate toughness and abrasion resistance such as crushing, degradation and disintegration. The percentage wear of the sample aggregates due to rubbing with steel balls is determined and is known as Los Angeles Abrasion Value

Get Price

The crushing value test of aggregate provides the resistance of an aggregate sample to crushing under gradually applied compressive load. Generally, the test is conducted on aggregate passing 12.5 mm and retained on a 10 mm sieve

Get Price

Calculate Aggregate Crushing Value. The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a percentage, the result being recorded to the first decimal place: Aggregate Crushing Value = W B W A 100. Where, W A is weight of surface-dry sample

Get Price

Mechanical Properties of Aggregates Aggregate Crushing Value Test (BS:812, part 3) Procedure • The material to be tested should pass a 14.0 mm (1/2 in.) sieve and be retained on a 10 mm (3/8 in.) sieve. • Dry the sample in an oven at 100-110 0 C for four hours. • Place the sample in a standard cylindrical mould and tamp it. • Put a plunger on the top of the aggregate and place the

Get Price

Note 1: A procedure for testing coarse aggregate larger than 19.0 mm [3 / 4 in.] is covered in Test Method C535. Thus coarse aggregates with a maximum size between 19 mm [3 / 4 in.] and 37.5 mm [1 1 / 2 in.] may be tested by Test Method C535 or Test Method C131/C131M

Get Price

the. aggregate which require to be assessed. Accordingly, the relevant test methods may be chosen from amongst the various tests covered in this standard. For the convenience of the user, the test methods are grouped into the following eight parts of Indian Standard Methods of Test for Aggregates for Concrete ( IS : 2386-1963 ):

Get Price

Mar 30, 2020 Procedure of Aggregate Crushing Value Test:-. Sieve the test material through 12.5 mm and 10.0 mm IS sieve. Take test samples of aggregates passing through 12.5 mm IS sieve and retained on 10 mm IS sieve (minimum 3 Kg). Dry theme in an oven for 4 hours at a temperature of 100 C to 110 C and then cool at room temperature

Get Price

APPARATUS 1) LOSS ANGELES Abrasion Machine 2) Coarse Sieve Shaker 3) Weighing balance 4) Sieve #12 5) Abrasive Charges ( m=439.8 g) 5.4. PROCEDURE 1) Sieve the sample in the coarse sieve shaker. 2) Clean the aggregates and dry them in an oven at 105-110 C to constant weight. 3) Conforming to anyone of the grading A to D or 1-3 as per table (a)

Get Price

Dec 19, 2019 If the aggregate crushing value is less than 10, it signifies an exceptionally strong aggregate. Whereas, if the crushing value is 35 or above, it would normally be considered as weak aggregate. After performing the test, the crushed material is separated and calculated in terms of percentage of the original weight taken in the mould

Get Price

The test sample is subjected to a total 15 such blows, each being delivered at an interval of not less than one second. The crushed aggregate is then removed from the cup and the whole of it sieved on the 2.36mm sieve until no further significant amount passes. The fraction passing the sieve is weighed accurate to 0.1gm

Get Price

Oct 03, 2019 Sampling for Crushing Test of Aggregate. For the Aggregate crushing value test, an aggregate sample passing through 12.5 mm IS sieve and retained on 10mm IS sieve is selected and dried to a temperature of 105 C to 110 C then cooled to room temperature. To fill the cylindrical measure mould about 6.5 kg of a sample of aggregate is sufficient

Get Price

May 17, 2019 The apparatus for the standard aggregate crushing test as per IS: 2386-1963 (Part IV) consist of the following: The test mold-a 15.2 cm diameter open-ended steel cylinder with square base plate; plunger having a piston of diameter 15 cm, a rod could be inserted for lifting or placing the plunger in the cylinder with a provided hole across the stem of the plunger

Get Price

Calculation of Aggregate Crushing Value The ratio of weight of fines formed to the weight of total sample in each test shall be expressed as a percentage, the result being recorded to the first decimal place. Aggregate crushing value = (W2 x 100) / (W1-W) W2 =Weight of fraction passing through the appropriate sieve W1-W =Weight of surface dry sample

Get Price

The crushing value of aggregates is measured in the ratio between the crushed aggregates, obtained from the IS sieve 2.36mm and the weight of the dried aggregate sample. At least three samples should be tested from the same batch and average value to get accurate results. The crushing value of aggregate = (W2/W1) x 100. Lab Report

Get Price

The test sample: It consists of aggregates sized 12.5 mm - 10.0 mm(minimum 3kg). The aggregates should be dried by heating at 100-110 o C for a period of 4 hours and cooled. 1) Sieve the material through 12.5 mm and 10.0 mm IS sieve

Get Price

The weight is recorded as W2. Aggregate Crushing Value (ACV) can be determined by using a simple formula: This test is repeated once or twice and the average crushing value of the aggregate is determined. The average crushing value in the different tests is the actual crushing value of aggregate

Get Price

1.The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a percentage, the result being recorded to the first decimal place: Aggregate Crushing Value = (B/A) X 100 where A = weight of oven-dried sample B = weight in 'g' of fraction passing through 2.36 mm IS sieve. 6.Video Aggregate Crushing Value Test

Get Price

May 20, 2021 Pune. Oct 22, 2017. #1. Aggregate Crushing Value Test. This format is useful for doing crushing value test as per IS 2386 part 4. It is important test

Get Price